Shopping Cart

Your cart is empty.

Your cart is empty.

JEENDA Flange Wheel Bearing Bushing 4PCS 741-0990B, 741-0990A, 741-0660, 741-0516B, 741-0516A, 941-0516 Compatible with MTD Cub Cadet Troy-Bilt LT1042 LT1045 LT1046 LT1050 SLT1550 SLT1554 Lawn Mowers

Free shipping on orders over $29.99

$6.50

$ 2 .99 $2.99

In Stock

About this item

  • Material: Nylon
  • Part Number:741-0990B, 741-0516B, 741-0990A, 741-0990, 741-0516A, 741-0516, 941-0516;Rotary 12857 Bushings and 11714 Bearings
  • Compatible with MTD Cub Cadet Troy-Bilt LT1042 LT1045 LT1046 LT1050 SLT1550 SLT1554 Mowers;Compatible with MTD Huskee Poulan Roper Yard Machine 1.0" x 3/4"
  • Details: Compatible with MTD 741-0660 Height:1.0″ ID:3/4″ OD:15/16″;Compatible with MTD 741-0990A Height:1 3/8″ ID:3/4″ OD:1″ Flange Dia:1 1/16″
  • Package Includes: 2 Flange Bushings and 2 Bushings



Product Description

JEENDA
JEENDA

741-0990B 741-0990A 741-0660

JEENDA PARTS
About Jeenda

JEENDA PARTS is committed to providing high quality and low cost products for the aftermarket general consumption.We have been deeply engaged in the parts field for many years.

Featured Products Include:

PTO Switch,Relay,Solenoid,AVR,Fuel Pump,Injector,ect....

  • Lawn Mover Replacement
  • Auto Parts Replacement
  • Engineering Equipment Replacement

JEENDA Lawn Mover Parts Series

  • Material Nylon

Part Number:

741-0990B, 741-0516B, 741-0990A, 741-0990, 741-0516A, 741-0516, 941-0516;Rotary 12857 Bushings and 11714 Bearings

Compatible with:

MTD Cub Cadet Troy-Bilt LT1042 LT1045 LT1046 LT1050 SLT1550 SLT1554 Mowers

  • Easy to install
  • Superior Material
  • 30 Days Without no Risk to Return

jack
Reviewed in Canada on January 31, 2025
Fit perfect
charles
Reviewed in the United States on March 15, 2024
This is not for a Husqvarna mower put I did use them on a Murray
Nicole
Reviewed in the United States on May 1, 2023
Waste of money. Used the old parts these were way too fragile felt like plastic
Tristan
Reviewed in the United States on December 7, 2023
Worked fine, just bevel the ends so they press in the wheel easier.
Jackie Searcy
Reviewed in the United States on October 3, 2023
The bushings are 4 parts, 2 for each wheel. You’ll need to press or drive the old bushings out of wheels. You will see instructions that show which bushing goes inside wheels next to engine or mower frame. Please measure the O. D. Of both bushings to make sure the O.D. Is same or slightly larger than the wheel I.D.’s. Don’t forget to grease both inside bushings in each wheel. I have done this twice in last couple of years. Always use small wood block (2X4) block and hammer to tap the bushings into wheels. Good luck and take your time.
Wanda J. Winkler
Reviewed in the United States on February 15, 2022
The Items were great and the price was great also.
D. Rainwater
Reviewed in the United States on November 5, 2022
I just installed these on my riding mower this morning, and am very much less than favorably impressed.The listing says they are made of nylon, which I find doubtful. They feel like cheap plastic, and that suspicion is supported by the fact that when I fitted my grease gun to the zerk fittings after installing, rather than detaching properly when I had given them enough grease, the fitting BROKE OFF -- ON BOTH BUSHINGS!!Further disappointing is the fact that they do not fit the axle very well, and leave the wheels a bit 'wobbly'. (So bad in fact that I removed both of the outer bushings (one on each front wheel) and replaced them with THE OLD BUSHINGS I was replacing! :/ The worn parts still work better than these NEW ones.I did manage to get my yard mowed today -- but I'll soon be looking for real OEM parts that hopefully will work as intended. I would NOT recommend this purchase.
John K
Reviewed in the United States on July 23, 2021
Inner set were loose in the hub, but just tight enough to use . Outer set were way to loose to use in the hub. Had to use my old ones on the outer. Ordered this by part number . Tractor was at my cabin 200 miles away. Both should have had the same OD and ID specs . Outer of what I received measured OD of 0.926" and ID of 0.796". Spindle was 0.750" and hub was 0.999". Then when I pumped grease into the inner bushings , the grease fitting broke off of both . They are just glued on and not 1 piece as the original Cub parts were, Good thing I greased everything as I assembled. I'll be buying original parts next time soon as I can no longer grease them.I ordered the correct parts from Cub yesterday . Their specs say the OD is 0.999" on both parts . Same part numbers. More money and longer ship time . But I already spent the money on this junk and the probably won't take them back after using half the order. Never again buying anything JEENDA.
Yvon Laviolette
Reviewed in Canada on July 20, 2021
Sur un côté de la roue pas problème l autre côté était trop petit trop de jeux dans la roue.
GMan
Reviewed in the United States on October 11, 2021
Works great good price