Your cart is empty.
Your cart is empty.Product Description
Carbide End Mill Cutter
Made of solid carbide (tungsten steel), high hardness, wear resistance, good toughness and heat resistance. Provide good cutting strength and drilling effect to improve efficiency.
Spiral and Sharp Flute
Spiral chip space design for fast and clean chip removal. Sharp cutting edge provides smooth cutting and no glitches.
Upcut Design
Upcut end mills can direct chips up and away from the milling area, leaving an unobstructed path to prevent tool breakage and extends the tool life.
Features
- Carbide can run at higher speed than high-speed steel.
- Designed with the base substrate without any coatings, suitable for wide ranges of applications.
- Different spiral end mills are available to meet your needs.
Wide Applications
Suitable for engraving, cutting, carving, milling, slotting, sculpturing in MDF, ABS, PVC, acrylic, nylon, plastic, wood, plywood, hardwood etc. Good for surface machining, 2D or 3D relief sculpturing. Use on milling and engraving machines. Use vertically and take good control of your CNC speed.
Amanda Knows
Reviewed in the United States on July 31, 2024
Poor quality. Leaves a rough finish. Tried all five pieces to get a hot job done but they just couldn't perform. Switched to a better brand and got a perfect finish.
D. A. Miller
Reviewed in the United States on March 24, 2024
I am using the bits on a cnc to cut parts that have several small holes. These cut with little resulting waste and are sized so I dont have tool changes. Lost two bits from being stupid, but no loss from cutting.
Al S
Reviewed in the United States on September 21, 2023
The 12mm cutter length is great for thicker stock. Be sure to move these slowly, as that extra length makes them very fragile. Broke a couple before I backed-off enough the motion speed. Still a good value IF you need 12mm. If you're not cutting that deep get a shorter cutter that's less fragile.
David Jones
Reviewed in Canada on April 23, 2023
Cutting 1/4" plywood on my CNC and the bit tends to rip the wood on a cross cut, but for my project, that is not an issue as I will be filling, sanding and painting. Overall, very pleased with my purchase.
Ray Davis
Reviewed in the United States on March 24, 2022
Fast cutting sharp good value
Hyrum Luke
Reviewed in the United States on December 12, 2022
These bits are simply amazing. I was able to cut out 12 of these lanterns before 1 broke. I've got my cnc set to cut at 0.30 depth per pass and cutting 60 inches a minute turning 18000 rpms on the spindle. Extremely durable and cheap.
john thompson
Reviewed in the United States on November 2, 2022
Easy of use
Michael
Reviewed in the United States on March 17, 2021
Have not used these yet but they do appear well made. And product was as described.
Dib
Reviewed in the United Kingdom on March 1, 2021
Not fit for purpose. Thought they were router bits. These are just small drill bits.
Samantha W.
Reviewed in the United Kingdom on September 18, 2020
These are not 1.5mm diameter.They measure at 1.4mm on digital gauges.If this isn’t a problem for you then they seem fine to work with but if you need precision... these are not great.
Jeff_B
Reviewed in the United States on August 2, 2020
I have some incredibly expensive end mills that I typically use for hardwoods, I'm not a fan of dulling out those $30 / end mill tools on things like "hardboard" or MDF - hence the $2.60 option. These have lasted a couple jobs per end mill using really conservative feeds and speeds ( 30 IPM, .65 mm depth per pass) and I can't complain. Don't buy these expecting them to last as long as your "Spektra" coated tools - expect them to be in the VALUE of $6.00 / tool for $2.60 each.
Recommended Products