Your cart is empty.
Your cart is empty.Product Description
- The Tracer AN series. Based on common negative design and advanced MPPT control algorithm, with LCD displaying running status, this product is artistic, economical and practical.
- The limitation function of the charging power and current and reducing charging power function automatic improve the stability which works even connecting oversize PV modules and in high temperature, and increase the professional protection chip for the communication port, further improving the reliability and meeting the different application requirements.
- With the adaptive three-stage charging mode based on a digital control circuit
- This modular solar controller can be widely used for different applications, e.g., Communication base stations, household systems, and field monitoring, etc.
- The communication port adopts professional protection chip, which can provide 5VDC power supply, and has over-current and short-circuit protection
- With RS-485 communication bus interface and Modbus communication protocol, it is available to meet various communication requirements in different situations
- Monitor and set the parameters via mobile phone APP or PC software
- Full-load operation without any drop in capacity within the range of working environment temperature
- Advanced MPPT technology, with efficiency no less than 99.5%
- Advanced MPPT control algorithm to minimize the maximum power point loss rate and loss time
- Wide MPP operating voltage range
- International famous brands of ST and IR's components of high quality and low failure rate are used, which can ensure the product‟s service life
- Compatible with lead-acid and lithium-ion batteries
- Extensive electronic protection
- Charging power and current limitation function
- Battery temperature compensation function
- Real-time energy statistics function
- Overheating power reduction function
- Multiple load work modes
- Charge Rated Current:30A
- System Voltage:12V/24V auto work
- Voltage: 100V
- Consumption: ≤12mA
- Battery Voltage Range: 8V ~ 32V
- RS485 communication interface: 5VDC/100mA
- Grounding type: Negative ground
- Battery types: Gel battery, Sealed lead-acid battery, Flooded battery, lithium battery, User-defined.
- The controller connection sequence is Battery--Load--Solar Panel, and discounect the system in the reverse order Solar Panel--Load--Battery
CAUTION:
- While wiring the controller do not close the circuit breaker or fuse and make sure that the leads of "+" and "-" poles are connected correctly.
- A fuse which current is 1.25 to 2 times the rated current of the controller, must be installed on the battery side with a distance from the battery not greater than 150 mm.
- If an inverter is to be connected to the system, connect the inverter directly to the battery, not to the load side of the controller.
3210AN MPPT Solar Controller
- 12V/24VDC Auto Working
- 100V Max. PV Open Circuit Voltage
- Compatible with lead-acid and lithium-ion batteries
- Advanced MPPT technology, with efficiency no less than 99.5%
MT-50
- Wide LCD screen displays the real time operational data and the working status in digital, graphic and textual forms.
- Basically used for monitoring and setting the controller, it automatically identifies the type, model and relevant parameter data of solar controllers.
RS485
- USB To RS-485 converter is used to monitor each controller on the network using Solar Station PC software and update the firmware.
- The length of cable is 1.5m.
RTS
- Acquisition of battery temperature for undertaking temperature compensation of control parameters, the standard length of the cable is 3m.
- The RTS300R47K3.81A connects to the port on the controller.
- NOTE: Unplug the RTS, the temperature of battery will be set to a fixed value 25ºC.
BeenThere
Reviewed in the United States on June 11, 2024
I'm not very good at installing electrical, so someone else installed it. It has worked perfectly so far.
GatorFan
Reviewed in the United States on May 12, 2024
I connected this to 4 flexible monocrystalline panels rated 100 watts each. Panels wired in 2 parallel sets, then series connected the 2 pairs for open circuit voltage around 45 volts. I am using a size 8D flooded lead-acid battery with about 200 amp-hours of capacity and 12 volts. The primary load is a Xantrex 3kW sine wave inverter. I was getting 125 watts solar charging in the 4pm late afternoon sun with the panels mostly flat and two panels shaded. Controller came in a kit with the remote, which I highly recommend. I only needed the manual for a minute at first, then everything in the setup was intuitive. This seems like a rugged, well built piece of electronic hardware. I will update this review if anything goes wrong, but initial functionality looks great.
Christopher Jacobs
Reviewed in the United States on October 28, 2024
This review is for Tracer4210AN.I had thought that 24v panels would charge my 24v panels. This is incorrect. I reached out to Epever support and they informed me I must supply 34v to charge 24v batteries.Thankfully I have two of the panels and moved from parallel to series and it's charging the batteries great. Looking at the panel voltage and the battery voltage and controller parameters, I'm not certain there's ever an ideal setup without lots of lower voltage panels where one can get the perfect pairing for the least loss, however in lower light I should still be supplying enough voltage to charge - not certain on amperage, time will tell.
Ronald W Kimball
Reviewed in the United States on August 17, 2023
I had Renogy and burned it up, my fault. This one has bigger holes for cables and it works Great.
davek
Reviewed in the United States on August 23, 2021
This charge controller seems to work alright although I am not impressed with it's low-light performance compared to Morningstar controllers I've used. The big problem is that the voltage registered by charge controller and displayed on the MT50 is off by about 0.5V near boost voltage. So, I've had to fudge the boost voltage to a higher value than I want the batteries to actually get to in order to compensate for the falsely high reading of controller. It's a cheezy fix and I shouldn't have to do that. There doesn't seem to be any calibration either and the discrepancy isn't always 0.5V, it's less at lower voltages. One nice thing is that the controller has a temperature cutoff to protect lithium batteries from charging at low temps. It is default set for 0 degrees C and says the user can change it. But I have not found any way to change it in any of the parameter menus, and try to get some help from Epever, it's hopeless.
Kevinmcdonald
Reviewed in Canada on December 5, 2021
Very easy to use, great product
Christian Dubord
Reviewed in Canada on January 20, 2021
Il n'est pas encore installé, mais il semble de bonne qualité
Panamama
Reviewed in the United States on September 5, 2020
Love this controller! I researched a lot before buying, and watched a lot of YouTube that recommended it. I was impressed with the company and how involved they seem to be with their products. The instruction manual is well done. Easy install. Syncs easily with the remote control panel which is easy to use. Great price. I think the blue brand that starts with a V is a rip off since this one does it all, including connecting to smartphone or laptop at much lower price.
T.@808
Reviewed in the United States on July 18, 2020
Controller is working great, easy to program and understand settings. It's a 40amp controller but have seen it peak at 45amp w/ no problems. Hooked up to 3x160w poly panels in Hawai'i, output is @ 2kwh/day, very happy with this unit. 🌴😁👍
James
Reviewed in the United States on June 2, 2020
Absolutely no problems and am very happy with this charge controller. It fully charges my batteries as I have had a hard time with my PWM controllers. Thanks. It's perfect for me.
Recommended Products