Your cart is empty.
Your cart is empty. The Active PoE Splitter splits a PoE signal into an 5VDC power and 10/100Mbps ethernet data source.
This device allows you to run ethernet cables from a POE Switch over long distance, and then split the PoE signal into a separate data signal and 5Vdc power sources in order to run an non-PoE devices.
Specifications:
Input: 44-56VDC max ; Shielded RJ-45 female;
Output: 5VDC 2.4A 12W; RJ-45 male
DC jack Micro USB
Length of Micro USB cable: 18.5cm
Operating Ambient Temperature: -10 to 45℃
Regulatory IEEE 802.3af
What is included
4x 5V PoE splitter
GrantL
Reviewed in Canada on March 21, 2025
Used to split RJ45 PoE cable to USB-C power for Wyze Cam AND RJ45 data connection (PoE tap). Note that RJ45 connection is 4-wire/data ONLY and does NOT support PoE/DATA device. Shame… if 8-wires passed thru to RJ45 would be useful for other POE/data devices while sharing PoE power.
Mitch
Reviewed in the United States on September 2, 2024
Used all four and they worked well for several months. Then one failed. Contacted Anvision and they refunded the cost of the failed splitter. Still the best deal on micro USB splitters.4/5 stars for the product, +1 for Anvision refunding the failed one.
Ray
Reviewed in the United States on October 11, 2024
Worked great! Love them.
Jojo Kraken
Reviewed in the United States on August 2, 2022
The rental house was rigged with POE camera that I didn’t have access too. This easily convert the POE Ethernet to microUSB. It is able to run my Wyze V3 without any issues.
Gerardo
Reviewed in Italy on August 21, 2019
Il prodotto funziona con le mie telecamere!!!
R.Z.
Reviewed in the United States on June 11, 2019
Inconsistent voltage/amperage across the splitter, I had to replace 3 times then I gave up and got a different PoE splitter from another seller, and those work flawlessly than this one! Get the "UCTRONICS PoE Splitter Gigabit 5V - Micro USB Power and Ethernet to Raspberry Pi 3B+, Work with Echo Dot, Most Micro USB Security Camera and Tablet - IEEE 802.3af Compliant" (product ID B07CNKX14C) instead of this. This 4-pk version was just a nightmare. I could not get the Raspberry Pi 3B+ to run at 100%, since the power LED kept going out and occasionally blinking. 1 out of 4 PoE splitter might work, but that's abysmal if you ask me. I expect all 4 to work, not just 1.
Bigbroseur
Reviewed in France on January 1, 2019
Avec un switch PoE ces découpleurs (splitter) fonctionnent à merveille;Certes un peu cher mais si il avait fallut tirer des câbles 220v je pense que je m'y retrouve
jeff
Reviewed in the United States on September 26, 2018
I bought two sets of these to power Raspberry Pi's, I am using Ubiquiti Managed POE switches. They immediately worked with the POE+ power sensing. (Some versions of firmware have POE disabled by default so check this if your having problems with these switches)However I didn't have a network connection. I needed to change the port settings on the switch from "auto detect Link speed" to manual and then "100mbit". Once I did this after 30seconds to 1minute the link light on the raspberry Pi's network interface then came on.Works fine with my -pi 1 b+pi 2pi zeropi zero Wpi 3+
USP357
Reviewed in the United States on September 26, 2018
Well I was not able to use on my project but they look like quality parts I was going to return them but miss my dead line for refund. but that's just my own fault. happy shopping.
ziggy
Reviewed in the United States on July 25, 2018
I'm using these to run Raspberry Pi computers in buildings to do envronmental monitoring and security. The devices are small and easily fit in the electrical box with the pi and interface boards. They provide the full current the pi needs and run perfectly well on POE ports from my Cisco swithches. They only pass 100 Megabit ethernet but that's fine since it's all the pi can do anyhow.,
Justin Osborne
Reviewed in the United States on June 29, 2018
Edit: May 23, 2019 – Been using these for a while now and they work great; however, they do cause interference on garage door openers (300mhz?). I had to remove it so my opener would work reliably again.Seems to power ok, but the micro USB plug is huge, so it won't fit into anything that's inset, like the Wyze Cam. However, I cut away some of the top and bottom using a razor knife and it fit perfectly and powered the Wyze Cam just fine.Just know that out of the box, the plug is too big. It's an easy fix though. This is also what the manufacturer/seller recommended I do.
Jon Gerdes
Reviewed in the United Kingdom on June 27, 2018
(Complete rewrite of my initial review and a drop of 5 star to 3) The USB power works fine. The ethernet does not.This device powers ESP8266s nicely but when plugged into a RaspPI 3B+ it manages power but no network connection. ethtool shows 10/100 half/full duplex being offered but no link.So, you do get USB power over a very long range but probably no network.
D. Koehler
Reviewed in Germany on December 27, 2018
Der POE Adapter funktioniert mit den alten Raspberry Pi's problemlos, beim neusten Raspberry Pi 3B+ gibt es Schwierigkeiten vermutlich kommt der Gigabit Netzwerk Chip nicht mit den 100 MBit des Adapters.
Recommended Products
